Search Results
Web results
Mixer Terminations
www.qsl.net › mixerterminations
www.qsl.net › mixerterminations
A good rule of thumb is that the mixer should be correctly terminated from the lowest ... The simplest form of DBM termination is a 50 ohm resistor but this increases ... A core locking compound should be used in the variable inductors to prevent ...
Understanding Impedance - Sound On Sound
www.soundonsound.com › techniques › understanding...
www.soundonsound.com › techniques › understanding...
Anyone who has read the technical specifications of any mixer, preamplifier, ... and inductors as a composite lump, and that's what we call the impedance. ... because each of the two parallel 600 ohm loads only receives half the signal power. ... for the spec sheet by measuring the input stage with a 50Ω source impedance.
Web results
Dual Gate MOSFET Mixers - Bibliothèque et Archives Canada
www.collectionscanada.gc.ca › tape17 › PQDD_0004
www.collectionscanada.gc.ca › tape17 › PQDD_0004
PDF
MOSFET mixer circuit is constmcted and measured with an RF input fiequency of 857. MHz, LO ... function of W input power with 50 ohm load. 66. Chapter 6.
Forum - Designer's Guide Community
www.designers-guide.org › Forum › YaBB
www.designers-guide.org › Forum › YaBB
Oct 20, 2002 — For the LNA, the 50 ohm source and load is physical. For the mixer, perhaps the load is a high impedance. ... circuit out with voltage sources, source impedances, and input impedances then derive the composite noise figure.
Impedance and impedance matching | - ePanorama.net
www.epanorama.net › newepa › 2016/02/20 › impedan...
www.epanorama.net › newepa › 2016/02/20 › impedan...
Feb 20, 2016 — ... capacitors and inductors as a composite lump, and that's what we call the impedance. ... Most typical impedance seen on cables are 50 Ohm single ended ... of 120 ohms is recommended with 120 ohm termination at each end of the ... Mixers typically only have LoZ and line level inputs, so plugging in the ...
AN00-011 - Frequently asked questions about mixers - Mini ...
www.minicircuits.com › app
www.minicircuits.com › app
PDF
The Q&As below cover general topics on the use of frequency mixers. ... This is about 1 dB higher than a typical "termination-insensitive" mixer. ... A. If the amplifier input does not appear as 50-ohms, there will be reflections back to the.
Microwave mixer using microstrip circular disk configuration
onlinelibrary.wiley.com › doi › mop.28723 › pdf
onlinelibrary.wiley.com › doi › mop.28723 › pdf
Schultz, Composite medium with simultaneously negative permeabil- ity and permittivity, Phys ... match with 50 Ohm microstrip lines of width w 5 3 mm have been optimized. ... due to the loading effects from the feed ports. The value of S11.
Reconfigurable CMOS Mixers for Radio-Frequency ... - QSpace
qspace.library.queensu.ca › Wang_Min_201006_MASc
qspace.library.queensu.ca › Wang_Min_201006_MASc
PDF
This thesis focuses on the design of radio-frequency (RF) mixers, including a broad- band downconverter mixer ... composite structure will be 0. ... where RL refers to the load impedance which is 50 Ω in a typical RFIC design and gmb3 is the ...
Impedance in Audio Technology
peavey.com › Impedance-in-Audio-Technology
peavey.com › Impedance-in-Audio-Technology
Composer Series · Composite Acoustics ... One ohm is the unit of resistance that will limit the current flow to one ampere when an electrical ... If the same 40 volts were delivered by the amplifier to a 4 ohm loudspeaker load, then we ... would pass signals out to 50 kHz, while the mixer with the 1,000 ohm source impedance ...