Heath Zenith 6103, Motion Sensor Wall Switch 6103 User's manual

Motion Sensor
Wall Switch
OFF
AUTO
ON
6103
The 6103 Motion Sensor Wall Switch detects motion to turn on lights
for a fixed time of 5 minutes. The unit has excellent sensitivity and
a 110° detection range. It can be used with incandescent lighting as
well as rapid start fluorescent lighting.
Installation is as easy as replacing a wall switch. However, some
codes require installation by a qualified electrician.
Included are:
• The sensor switch
• Cover plate
• 3 wire connectors
• 2 large screws
• 2 small screws
Features include:
• 110° motion detection angle
• Fixed ON TIME – 5 minutes
• Works with incandescent and rapid start fluorescent lighting
• Works with motors up to 1/8 hp
• Slide switch selectable OFF, ON, and AUTO modes
INSTALLATION
20 ft.
(6.1 m)
SELECT A LOCATION
The sensor is more sensitive to motion across
the front of the sensor than to motion towards
the sensor.
The detector senses heat in motion and possibly heat sources that change temperature
quickly. Therefore, to avoid false triggering,
avoid placing the sensor where it will be aimed
at air conditioners, heaters, and other sources
of heat or cold.
10 ft. (3.5 m)
0
Figure 1 - Typical Plan View of
Coverage
© 2008 HeathCo LLC
598-1349-00
Typical Installation
WARNING: Turn power off at the
circuit breaker before wiring.
Installing Sensor
Removing Control Panel Cover
1. Remove the decorative cover plate (secured
by two small screws).
OFF
AUTO
1. Remove existing wall switch from junction
box.
2. Connect electrical leads of sensor as shown in
Figure 3. Before installing sensor into junction
box, make sure there is no wire exposed at
each connection.
3. Mount sensor into junction box using two large
mounting screws provided.
4. Turn the power back on at the circuit breaker.
5. Set mode selection switch to the AUTO position. When unit stabilizes (about 1 minute),
the sensor is ready to detect motion. If sensor
detects motion, the lights will turn on. The
lights will turn off 5 minutes after motion is
no longer detected.
ON
Figure 2 - Removing Control Panel Cover
To Lighting Load
Black
Neutral
Return
Lighting Load
Green ground wire to
junction box screw or
grounding wire.
Mode
Selection
Switch
OFF
AUTO
ON
Black
Figure 3 - Connecting Electrical Leads of Sensor
Line
“Hot”
598-1349-00
Using Motion Sensor
Wall Switch
Completing Installation
1. Replace the decorative wall plate. In installations where the Heath®/Zenith motion sensor
switch is combined with other switches or
outlets on an expanded box, you will need to
purchase a combination wall plate. Various
combination wall plates are available at home
centers and electrical supply stores.
2. Slide the mode selection switch a couple times
to make sure it moves freely.
Mode Selection Switch
This switch allows you to select one of three modes
of operation: OFF, AUTO, or ON.
OFF: Lights stay off.
AUTO: Lights automatically come on when motion is detected. The lights will turn off 5 minutes
after motion is no longer detected.
ON: Lights stay on continuously.
SPECIFICATIONS
Electrical Input.................................................................................................................120V, 60 Hz.
Fluorescent Load....................................30 Watts minimum, Up to 400 Watts Maximum Rapid Start
Motor Load....................................................................................................Up to 1/8 HP Maximum
Incandescent............................................................................Up to 500 Watts Maximum at 120VAC
On-Time...................................................................................................................Fixed – 5 Minutes
Coverage................................. up to 10 ft. (3.5 m) at 110°, up to 20 ft. (6.1 m) in front of the sensor
HeathCo LLC reserves the right to discontinue products and to change specifications at any time
without incurring any obligation to incorporate new features in products previously sold.
598-1349-00
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SYMPTOM
POSSIBLE CAUSE
Light does
not come
on.
1. Circuit breaker or fuse is
turned off.
2. If the lamp being controlled
has another switch, it may be
turned off.
3. Bulb is defective.
4. LIGHT control is set too far
toward the dark position.
5. Mode switch is set to OFF
instead of AUTO.
6. Poor connection.
Light does
not turn off.
1. Incorrect wiring.
2. Mode switch is set to ON
instead of AUTO.
3. Motion is still present.
4. Fixed time (5 minutes) has
not yet expired.
Light comes
on for no
reason in
the AUTO
mode.
1. Heating or cooling objects
(such as air vents, appliances,
or drafts through the wall box)
are causing false triggering.
2. Switch on the sensor has been
turned off and back on.
3. There was a momentary power interruption. The light will
turn off automatically when
the “on” time expires.
Lights do
not stay on
in the AUTO
mode.
1. Motion has stopped in the
room.
Technical Service
Please call 1-800-858-8501 (English speaking only) for assistance before returning product
to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.hzsupport.
com. If the problem persists, call* for assistance at 1-800-858-8501 (English speaking only), 7:30 AM to
4:30 PM CST (M-F). You may also write* to:
HeathCo LLC, P.O. Box 90045, Bowling Green, KY 42102-9045
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of
Purchase, and Place of Purchase.
No Service Parts Available for this Product
TWO YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to
state or province to province.
For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship
will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and
other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any
furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience,
installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that
a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY
ON THE PART OF HeathCo LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some
states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.
598-1349-00
OFF
AUTO
ON
INSTALACION
6.1 m
3.5 m
0
598-1349-00 S
INSTALACION DEL DETECTOR
OFF
AUTO
ON
Negro
Retorno
nuetro
CARGA DE LUZ
OFF
AUTO
ON
Negro
USO DEL INTERRUPTOR DE
PARED DEL DETECTOR DE
MOVIMIENTO
INTERRUPTOR SELECTOR DE FASE
GUIA DE SOLUCION DE PROBLEMAS
SINTOMA
POSIBLE CAUSA
SINTOMA
POSIBLE CAUSA
La luz no se
prende
La luz no
se apaga.
SERVICIO TÉCNICO
598-1349-00
OFF
AUTO
ON
INSTALLATION
6,1 m
598-1349-00
© 2008 HeathCo LLC
Installation type
INSTALLATION DU DÉTECTEUR
OFF
AUTO
ON
Noir
OFF
AUTO
ON
Noir
598-1349-00
UTILISATION DE
L’INTERRUPTEUR MURAL À
DÉTECTEUR DE MOUVEMENT
INTERRUPTEUR DE SÉLECTION DE MODE
SPECIFICATIONS
11
DÉPANNAGE
SYMPTÔME
CAUSE POSSIBLE
SYMPTÔME
POSSIBLE CAUSE
SERVICE TECHNIQUE
12
598-1349-00