Ken A Vision Video Flex 7100 Instruction Manual
Video flex 7000 series
Hide thumbs
Also See for Video Flex 7100:
- Instruction manual (6 pages) ,
- Specifications (1 page) ,
- Product catalog (28 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Ken A Vision Video Flex 7100
Summary of Contents for Ken A Vision Video Flex 7100
- Page 1 Video Flex 7000 Series Instruction Manual 7100 7100P 7200HD 7300 7300P 7600 7600P...
- Page 2 Video Flex 7000® Series Instruction Manual ® Thank you for your purchase of a Ken-A-Vision Video Flex 7000 series camera! You have acquired a high resolution solution to any presentation need, be it classroom or conference room. Images captured by your camera will be transmitted directly to your TV/Monitor, Projector, or VCR (7100, 7100P , 7300, 7300P ,) or through your computer to a Projector, DVR, Flash Drive or other digital device (7200HD).
- Page 3 7200HD • Attached USB Cable • Powered by USB So No Separate Power Cable • 28mm Microscope Adapter • Ball and Socket Head • Discovery Scope Kit • Applied Vision™ Software CD • Applied Vision Manual 7600 - (Same parts as 7100,7300 7600P -(Same parts as 7100P , with following additions) 7300P with following additions)
- Page 4 Now plug the small, round male plug at the other end of the power supply, ® into the Video Flex camera, in the slot marked PWR, in the middle back of the unit. ® Plug the Video Flex camera unit into your power source. If unit was purchased or shipped to the country of use, the plug has the correct male adapter and is rated for the correct voltage.
- Page 5 (plug on back of unit, at the far left of center). If unit is powered up and red light of unit is on, video image from camera should appear on your S-Video output device. • TV/Monitor Connect the composite (RCA type) yellow video cable or the S-Video ®...
- Page 6 dependent upon your computer set up. See the owner's manual of the computer for the operating procedures. Note : The USB cable provides ample power to the camera, no separate power supply needed. Note2: On the 7600 and 7600P , if the USB is connected, THE POWER SUPPLY DOES NOT NEED TO BE CONNECTED.
- Page 7 7600, 7600P (in digital mode), 7200HD On the 7600/7600P units, the switch on the base can be used even when camera in digital operation. But additionally the positive/negative image may be toggled on/off using the Applied Vision™ Software. (If your version of Applied Vision™...
- Page 8 clockwise direction, adding an additional amount of force to lock it in place. 7. Focusing: ® ® The Video Flex uses the patented Quick Focus C-mount lens. The focusing ring, located on the camera head, is similar to that of a 35mm camera. The new ergonomic design makes focusing with one hand a snap.
- Page 9 NOTE: Before installing the microscope eyepiece adapter, measure the size of the outside diameter of the microscope eyepiece to be sure adapter will fit over the end of the eyepiece. Remove the rubber eyecup if present. 1. Place the microscope eyepiece adapter over one (if Dual-Headed or Binocular) of the microscope's eyepieces.
- Page 10 o One of the small plastic specimen holder envelopes and the box holder. The Bags are held by the small slit in the ends of the box holder. • Now place the shaft of the holder into the small opening located at the end of the telescoping tube.
- Page 11 ® Video Flex Accessories Expand the capabilities of your Video Flex with accessories. Additional accessories are available on our Web-site at www.ken-a-vision.com. Replacement Parts VFDS....Discovery Scope Kit VFPSEU....Discovery Scope Kit 2200 VFPSUSA....Power Supply 1100 VFEA280....28mm Eyepiece Adapter VFC12AV...12' Audio/Video Cable VF8MM....8mm Lens Ken-A-Vision has over 65 years of history providing quality products to institutions world wide.
-
Page 12: Information To The User
Camera complies with Class A and B, part 15 of the FCC Rules. Use only Ken-A-Vision Video Flex parts. The Power Supply and Charger are made exclusively for the Video Flex. Failure to use non-Video Flex parts will void your warranty. INFORMATION TO THE USER Changes or modifications not expressly approved by the party responsible for compliance could void the user's author-...